PILLOBALLS

bearings egypt, egypt bearings, PILLOBALLS
Types
IKO PILLOBALLS are avasilable in the various types shown in the following table.
Table 1 Type
Pilloball
spherical
bushing-
insert type		 Pilloball rod-ends(1)
Insert type Die-cast type
Female threadMale threadFemale thread
PBPHSPOSPHSA
Pilloball spherical bushing-insert type
These bushing have bushes made of a special pliable copper alloy inserted between the outer ring and inner ring which is treated with chromium plating on the spherical surface after hardening and precision finishing. They are rigid bushings with wear resistance properties, and are directly mounted to the shaft and housing They have oil holes and oil grooves on the outer ring. Where there are heavy radil and thrust loads, IKO SPHERICAL BUSHINGS, whose sliding surface on the inner and outer ring have been MoS2-treated,are recommended.

Pilloball rod-ends-insert type with female thrust
These rod-ends have bushes made of a special pliable copper alloy inserted between the body with female thread which is treated with zinc chromate plating and the inner ring which is treated with chromium plating on the spherical surface after hardening and precision finishing. They are rigid rod-ends with wear resistance and anti-corrosion properties and are use in in connection with the shaft. There is a grease nipple on the body.

Pilloball rod-ends-insert type with male thrust

These rod-ends have a male thread. Their structure and performance are the same as those with a female thread. However, in case of POS 5 and 6, they have no grease nipple and are directly lubricated through the oil hole in the body

Pilloball rod-ends-die-cast type with female thrust

The hardened end then mirror-finished spherical inner ring is held by the special zinc die-cast alloy body, and there is almost complete contact across the sliding surface.These rod-ends are very economical and have wear resistance propertiesand There is a grease nipple on the body.

Accuracy standard
The accuracies for IKO PILLOBALLS are shown in table 2.1and 2.2
The radial clearance for the insert type is 0.035 mm (Maximum).
Table 2.1 Dimensional toierance
Type Part Symbol Tolerance
PB Inside diameter of inner ring d H 7
Outside dimeter of outer ring D h 6
Width of inner ring B 1 0
-0.1
Widtr of outer ring B +0.1
PHS
P0S		 Inside diameter of inner ring d H 7
width of inner ringB10
-0.1
PHSA Inside diameter of inner ring d +0.063
-0.012
Width of inner ring B1 See Table 2.2

Table 2.2 Dimensional toierance (Width of inner ring for PHSA SERIES)
Part Symbol Rod-end number Tolerance
Width of
inner ring 		B1 PHSA 14 and downwards0
-0.2
PHSA 20 and downwords 0
-0.3
PHSA 22 and downwords 0
-0.4
Fit
The recommended fit for IKO PILLOBALLS is shown in table 3.
Table 3 Recommended fit
Condition Shaft Housing bord(1)
Normal condition h7 H 7
With indeteminate lode n6, p6 N 7

Agent : RIV Company
6 Orabi Street,
P.O.Box 101, Cairo 11511, Egypt
Tel. : +202-5749921, +202-5759921
Fax. : +202-5776236, Tlx. : 92808 RIV UN
E-mail : iko@riv.org

Back to IKO Bearings Egypt, Egypt Bearings web page.
Ball Bearings
Stieber Freewheels
RIV Company
Miniature Bearing
American Bearings
Ceramic Bearings
Dental Bearing
Ceramic Bearing | Miniature Bearing | Skateboard Bearing | Hybrid Ceramic Bearing
Full Ceramic Bearing | Fishing Reel Bearing | Linear Bearing | Thrust Bearing | Needle Bearing

This page is always under construction, last update is in February 1999.
you are visitor number since 25th May 1999








IKO Nippon Thompson, IKO Nippon Thompson, IKO Nippon Thompson, IKO Nippon Thompson,